» Articles » Proportional valve types for different applications

Proportional valve types for different applications

When it comes to Proportional Valves, they are well-suited to a number of different applications in machinery, basic processes and hydro-pneumatic systems.  They provide compact and cost effective solutions for controlling pressure or flow at low flow rates.

Proportional valve

With so much differentiation and sources of supply, it is important to ensure you are picking the correct proportional valve to suit your application. This article will describe the important considerations you must take into account when selecting the correct proportional valve.

Proportional Valve Set Points

The first things to consider are:

  • What are the maximum and minimum pressures that the valve is likely to experience?
  • What are the flow ranges the valve is likely to experience?

Static Set Point

Pressure or Flow will be Fixed With Infrequent Changes

Typical Applications:

  • Spot welding – where a valve is used to control pressure to a cylinder that applies the pinching force. The pressure will be set dependant on the material type and thickness being welded and will remain fixed until the machine is set up for a different material.
  • Leak testing – where a fixed pressure is applied to a component to check for soundness. The pressure will generally be fixed for a specific type of component but has provision for adjustment when the application is changed.

Dynamic Set Point

Pressure or Flow will Change at a High Frequency

Typical Applications:

  • Pressure control valves connected to cylinders operating a flight simulator. Signals from the simulator control system constantly adjust the pressure in the cylinders to move the simulator cabin.
  • Material testing where the pressure output of a valve is steadily increased until the material under test fails.

Step-By-Step Point:

Pressure or Flow will change but at a Low Frequency

Typical Applications:

  • A filling system where, as the container being filled approaches the required fill level, the flow rate is adjusted down so that the final filling happens at a lower rate.
  • The control of gas to a burner on a cooker. This application would require different flow rates of gas dependant on the amount of heat required.

Adjusting Set Points

Another consideration when selecting a valve may be the means by which you want to adjust the setting, whether that is a set pressure or a set flow rate. As discussed above, the set point can be static, dynamic or ‘step by step’.

  • Some valves enable you to adjust the set point by sending an analogue control signal over the power cables or by using some sort of fieldbus communications.
  • Others have a local interface
  • Some enable you to communicate with the device via a PC and an RS 232 interface (this enables a far greater degree of tuning and optimisation to take place.

Actuation of Operation of your Proportional Valve

Engineers should also consider the type of operation they require. Different operation methods for proportional valves could be:

  • Proportional solenoids: valve position is adjusted based on a varying voltage across the coil. The higher the voltage the greater the magnetic current and the more the valve spindle moves. It tends to give short response times and has an extremely low hysteresis.
  • Pulsed solenoids: uses small solenoid valves that load and unload pressure in a control chamber, allowing the valve to open and close.
  • Piezoelectric elements: Their highly compact size makes piezoelectric operated valves ideal for use in portable and table top machines such as medical equipment, measuring systems and gas analysers. The valves have very low power consumption and can even be operated by batteries or solar cells.
  • Pneumatically operated and controlled by a positioner: When looking at larger capacities and larger flow rates it may be necessary to move to a valve fitted with a positioner. The positioner acts as a pilot, enabling air to enter and vent from a diaphragm or a cylinder which enables the much larger valve to operate.

The intention of this article is to discuss some of the factors that must be considered when specifying and purchasing proportional valves. For more information, please leave comments below, post a technical question in the Solution Centre or email us at [email protected].

Company Profile

Process Industry Forum

The leading online technical resource centre for the Process Industry.

Get the latest process industry news

Interested in receiving even more industry-leading news from Process Industry Forum delivered directly to your inbox? Then sign up to our free newsletter. Bringing you the latest news, trends, innovations and opinion from across the process industry, our exclusive newsletter gives you all the industry insights of the moment in one, easy-to-digest bulletin. Stay ahead of the competition with regular process industry news instalments from PIF.


    Our
    Partners